By Instruction for Installing a Bathtub
By Instruction for Installing a Bathtub
Blog Article
Were you interested in content about How to Install a Bathtub?
Mounting a tub isn't precisely brain surgery, yet it does need strong plumbing, carpentry, and sometimes, tiling abilities. Changing an old bath tub with a new one is additionally a reasonably hard task. If the old bathtub is easily available, the task can move speedily; if you have to open up a wall surface to eliminate the old bathtub and also position the brand-new bathtub, the job is much harder. In either case, the project is within a house handyman's skills, although you will require an assistant to leave the old bathtub and embeded in the new one. Make sure you have certified yourself for the job and also are comfortable attempting it. As opposed to working with a contractor to take control of a halfway-completed task, it is better to consider employing one prior to you start. Chances are you may require an expert plumber to make tube links.
This write-up will certainly help you mount a new bathtub in your washroom if you have already acquired a brand-new bathtub as well as don't need to change the arrangement of your previous water pipelines.
Your devices as well as material list ought to make up the following:
Planning for the Setup
To start with, the sustaining frame provided with the bathroom must be fitted (if required) according to the supplier's directions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to see to it that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the taps system to avoid strain on the bathtub.
Fit the flexible faucet ports to the bottom of the two taps using 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet with the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you make use of all of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its final setting.
Removing Old Taps
If you require to replace old taps with new ones as a part of your installment, then the first thing you must do is disconnect the water supply. After doing so, turn on the faucets to drain any water staying in the system. The process of removing the existing taps can be quite troublesome because of the restricted accessibility that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the faucets. Have a towel all set for the staying water that will come from the pipelines. Once the supply pipelines have been removed, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single taps from transforming throughout this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleansed of any type of old sealing compound.
Prior to moving on to fit the brand-new taps, contrast the pipeline links on the old faucets to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the new faucets to fit.
Mounting the Bathtub
Using the two wooden boards under its feet, place the bathtub in the needed setting. The wood boards are handy in evenly spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 small factors.
The next goal is to ensure that the tub is leveled all round. This can be achieved by inspecting the level and adjusting the feet on the bathtub up until the spirit level reads degree.
To install faucets, fit the bottom of the outermost flexible faucet connector to the ideal supply pipeline by making a compression join; after that do the same for the other tap.
Turn on the water system as well as check all joints and also brand-new pipework for leakages and tighten them if essential. Fill up the tub as well as likewise check the overflow electrical outlet and also the normal outlet for leakages.
Ultimately, repair the bathroom paneling as explained in the supplier's user's manual. Tiling and also securing around the tub ought to wait up until the bath tub has been made use of at the very least when as this will settle it right into its last setting.
Suitable New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to prevent damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end gives a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly call for minimizing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the placing hole in the bath/basin making sure that the washing machines remain in location between the tap and also the sink. Secure the faucet in place with the supplier supplied backnut. Once the tap is securely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical tap ports. The previous type must be attached to the faucet ends initially, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the location where the bath meets the tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to split a rigid seal, creating the water to penetrate the wall surface between the bathroom as well as the tiling, bring about complications with moisture and feasible leaks to the ceiling listed below.
You can select from a range of coloured sealers to assimilate your fixtures and also fittings. They are offered in tubes and cartridges, and also can sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with spins of soaked paper or soft rope. Bear in mind to constantly fill the tub with water before securing, to allow for the motion experienced when the bathtub is in use. The sealant can break rather very early if you do not consider this movement prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise quickly offered on the marketplace. It is recommended to fit the ceramic tiles utilizing water-resistant or water resistant glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I stumbled upon that piece about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround while surfing the internet. Be sure to set aside a second to share this write-up if you liked it. Thanks for your time. Please visit our blog back soon.
Learn More Report this page